|
|
|
|
Cleaning and Maintenance
Solutions for use with
Cleaning, Renovation and Maintenance |
|
Intensive Cleaning |
It is important to keep floors
scrupulously clean before and during fixing and sealing. LTP has
three intensive cleaning products. 1) LTP Grout Stain Remover Cleans most lime based stains, cement films, residual grout stain, plaster / dust and mineral salt stains 2) LTP Grimex Cleans oil grease, general dirt and grime, old wax layers, old acrylic seals, rubber sole marks etc. 3) LTP Power Stripper For intensive cleaning of heavily contaminated floors and removal of oxidised boiled linseed oil |
Renovation |
Dull or dirty floors may be
restored by the following procedures: 1) Floors sealed with linseed oil / beeswax a - use LTP Grimex or Genuine Turpentine to remove surface layer of wax b - apply one coat of LTP Cleartone, following instructions, to replenish the linseed oil seal c - allow 24 hours of the LTP cleartone to cure and re-wax with beeswax. 2) Floors sealed with LTP Ironwax and Ironwax Satin a - Remove surface seal by using LTP Grimex b - Neutralise the Grimex solution with a damp sponge and allow to dry thoroughly c - Reseal using LTP Ironwax or Ironwax Satin 3) Floors sealed with Mattstone or Colour Intensifier and Stain Block a - Wash floor thoroughly with LTP Grimex b - Neutralise the Grimex solution with a damp sponge and allow to dry thoroughly (up to three days) c - Re-apply LTP Mattstone or Colour intensifier, following instructions. |
Everyday Maintenance |
Floors should be regularly
swept and routinely washed with an appropriate maintenance product.
LTP has two cleaners for every day use. 1) LTP Floorshine Which may be used on glazed ceramics, unsealed floors and floors sealed with LTP Ironwax / Ironwax Satin / Glaze Protector or similar acrylic sealing products. LTP Floorshine contains small amounts of acrylic , which help develop a surface "shell" as the floor is washed. 2) LTP Waxwash Which may be used on, unsealed floors, floors sealed with Linseed Oil / Beeswax and floors treated with LTP Colour Intensifier and Stain Block / LTP Mattstone and LTP MPG sealer. |
|
Stain Removal Surface Blemishes  |
Floor seals are not a permanent
impenetrable barrier to staining, fluid contaminants, left on the
floor for more than 30 minutes, may produce minor discolouration.
Such marks may be minimised by the following methods. In all cases,
remove spillage as quickly as possible and wipe over floor with a
damp cloth. 1) Floors sealed with Linseed Oil / Beeswax After wiping up the spillage work over the affected area with a little beeswax and buff to a shine. 2) Floors sealed with LTP Ironwax or Ironwax Satin Use a little diluted LTP Grimex on a cloth to remove spillage. Neutralise solution with water. When dry reseal the area with more LTP Ironwax or Ironwax Satin 3) Floors sealed with Mattstone or Colour Intensifier and Stain Block or MPG Use a little diluted LTP Grimex on a cloth to remove spillage . Neutralise solution with water. When dry reseal with more LTP Mattstone, Colour Intensifier and Stain Block or MPG sealer. |
Oil and Grease Stains  |
1)
LTP
Fuller Earth On Recent spillages sponge the stain as much as possible with a clean cloth without rubbing, going from the outside to the middle of the stain. Powder the stain with LTP Fuller Earth. Leave for 30 minutes and delicately brush away. Apply again if necessary. In all cases it may be necessary to re-seal surfaces that have been treated. 2) LTP Spot Stain Remover On older spillages and stubborn oil and grease marks pour directly onto the stain and leave for about 5 minutes. Powder the stain with LTP Fullers Earth, wet the powder again with the LTP Spot Stain remover and cover it once more with the LTP Fullers Earth so the surface remains dry. Leave to react for about 24 hours. Brush away the powder and rinse well with a sponge and water. In all cases it may be necessary to re-seal surfaces that have been treated. |
|
Home - Cleaning - Maintenance - Application - Product Selector - Links - Purchase Online |
|
